FOX EPOTHANE® TOPCOAT CLEAR is an epoxy resin-based, two-component, solvent-free, self-levelling, transparent topcoat floor coating material with high chemical and mechanical resistance. It enables the achievement of glossy, hygienic and liquid-impermeable surfaces.
Colour Palette
Transparent
Packaging
5 kg
Product Description
FOX EPOTHANE® TOPCOAT CLEAR is an epoxy resin-based, two-component (A+B), solvent-free, self-levelling, transparent topcoat floor coating material. Thanks to its high chemical and mechanical resistance, it provides long-lasting protection in areas of intensive use. With 100% solid content, it does not shrink after application; it forms a glossy, hygienic and liquid-impermeable surface. Adhesion strength to concrete is ≥1.5 N/mm² and Shore D hardness reaches 85 in 7 days. Applied by roller; a second coat can be applied if desired.
Advantages
- Has high chemical and mechanical resistance.
- Easy to maintain and clean.
- Flowable.
- Provides hygienic environments.
- Liquid-impermeable.
- A glossy topcoat finish is achieved.
- High adhesion strength.
Usage Areas
- Areas where decorative flooring is desired
- Areas requiring chemical and mechanical resistance
- Airports
- Galleries and shopping centres
- Supermarkets
- Shops and showrooms
- Hotels
- Hospitals and nursing homes
- Clinics
- Schools and nurseries
- Areas where hygiene is required
Application Steps
- 1
Surface Preparation
The surface to be coated must be clean, dry and free from all foreign matter such as dust and dirt. Surface moisture content must be below 4%; there must be no rising damp according to ASTM (polyethylene sheet test). Concrete surfaces must be at least 3 weeks old, and a vapour barrier layer must be created for floors laid on ground soil.
- 2
Ensuring Application Conditions
Surface, ambient and material temperatures must be between +10°C and +30°C. Relative air humidity must be a maximum of 80%. The floor temperature must be kept at least +3°C above the dew point. Materials should be brought to the application area 1–2 days in advance and allowed to acclimatise to ambient conditions.
- 3
Mixing
After component B has been fully added to component A, the mixture is stirred using an electric mixer at 300–400 rpm with an epoxy/polyurethane mixing paddle for at least 3 minutes until a homogeneous mix is obtained. Excessive mixing should be avoided to minimise air entrainment.
- 4
Application
FOX EPOTHANE® TOPCOAT CLEAR is poured onto the surface, spread with a trowel and then evenly rolled with a roller. A second coat can be applied depending on the desired surface finish. Consumption is approximately 0.25 kg/m² (by roller).
- 5
Tool Cleaning
After application, tools and equipment used should be cleaned with solvents such as FOX CS810 or FOX C380. Once the product has cured, it can only be removed from the surface by mechanical means.
- 6
Curing and Protection
After application, the coating must be protected from water and physical contact for at least 24 hours. Full curing is completed in 7 days at +20°C.
Critical
After application, the coating must be protected from water and physical contact for at least 24 hours. In case of water contact, softening and blistering will occur on the coating; the coating will need to be completely removed and reapplied.
Critical
Surface temperature, ambient temperature and material temperature must be a minimum of +10°C and a maximum of +30°C. Application must not be carried out outside this range.
Critical
Concrete surfaces to be coated with epoxy/polyurethane must be at least 3 weeks old prior to application.
Critical
Surface moisture content must be below 4%. There must be no rising damp according to ASTM (polyethylene sheet test).
Critical
The floor temperature must be at least +3°C above the dew point. Pay attention to dew formation and condensation.
Critical
Mixing must be carried out with an electric mixer at 300–400 rpm and an epoxy/polyurethane resin mixing paddle. Otherwise, air bubbles will form on the coating.
Important
Relative air humidity must be a maximum of 80%.
Important
Materials to be used should be brought to the application site 1–2 days in advance and allowed to acclimatise to ambient conditions.
Important
In cold weather, packaging should be kept at +20°C–+25°C to bring the materials to a ready-to-use condition.
Important
Rain, dust, wind, animals and insects must be prevented from entering the building while the coating is still fresh.
Important
A vapour barrier layer must be created for floors laid on ground soil.
Important
The product must be stored between +5°C and +30°C, away from direct sunlight, in a cool and dry environment. Shelf life is 12 months from the date of manufacture.
Important
It is dangerous to approach storage and application areas with open flames; areas must be ventilated.
Important
Work clothing, protective gloves, goggles and a mask must be worn during application. Contact with skin and eyes must be avoided; in case of contact, wash thoroughly with plenty of water and soap. In case of ingestion, consult a doctor immediately.
Important
Must be stored out of reach of children. Food and beverages must not be brought into application areas.
Information
Consumption figures are given for ideal conditions at +20°C. It should be noted that consumption will increase on uneven surfaces and in cold weather conditions.
Information
The technical values above are given for +23°C and 50% relative humidity. Higher temperatures shorten the working time; lower temperatures extend it.
Related Products
Similar products to this item
